Counter Strike 1.6 - Z-Bot
File Info: Counter Strike 1.6 - Z-Bot
Description: Counter Strike 1.6 - Z-BotZ-bots offers different commands including adjusting bot difficulty levels, weapons, controls, numbers, navigation commands, and more.
1. Download: ZBot - CS Bots
Before You start installing Zbot it might be a good idea to backup your current settings just in case. Either backup your entire cstrike folder or just the file "liblist.gam" (this is where the changes are made).
Unzip the entire content of the zip to your Counter-Strike folder. Should look something like this:
You will be asked to replace some files, including liblist.gam. Replace all files.
3. Start playing
This is it. You have now installed Zbot! Now just start Counter-Strike, make a New Game. Now you will need to add the bots to the game. This is done either with the console or by pressing "H". Pressing "H" will bring up the command menu. If you prefer the console, commands are listed below.
When the first bot joins the
1. Changing command menu button
By default the command menu is bound to "H". To change this bring up the console and type:
bind "button" "+commandmenu"
2. Bot Commands
Causes a bot to be added to the game. "bot_add" will add a bot to the team specified by the "bot_join_team" cvar. "bot_add_t" and "bot_add_ct" forces the bot onto the respective teams.
This command takes either the name of a bot, or the keyword "all" - causing all bots in the game to be killed.
This command takes either the name of a bot, or the keyword "all" - causing all bots in the game to be kicked.
These commands are shortcuts that set the bot_allow_* cvars accordingly.
This cvar determines the difficulty of all newly created bots (existing bots will retain the difficulty setting they were created with). Zero = easy, 1 = normal, 2 = hard, 3 = expert. Difficulty values higher than 3 are reset to 3.
Setting this cvar to a nonzero value will cause the given number of bots to be maintained in the game. If a bot is kicked, a new bot will be added to maintain the quota. To disable the quota, set it to zero.
bot_join_team [ct, t, any]
Determines which team the bots will join.
If nonzero, the bots will wait to join the game until at least one human player has joined.
All of the "bot_allow" cvars can be either 0 or 1. If zero, the bots will not buy or use the given category of weapon.
If nonzero, allows bots to occasionally "go rogue". Rogue bots just "run and gun", and will respond to all radio commands with "Negative".
NAVIGATION MESH EDITING
Each of the following bot_nav_ commands operate on the navigation mesh, allowing hand-tuning of the automatically learned data. It is recommended that these commands be bound to keys for ease of use while editing.
CAUTION: There is no "undo" operation. Save your navigation mesh often.
Marks the currently selected nav area for later operations.
Deletes the currently selected nav area.
Splits the currently selected nav area into two new nav areas, along the white split line.
Merges the currently selected nav area and a previously marked nav area into a new, single nav area. The merge will only occur if the two areas are the same size along the merge line.
Creates a ONE WAY link from the currently marked area to the currently selected area, telling the bots they can walk FROM the marked area TO the selected area. For most areas, you will want to connect the areas in both directions. However, for some "jump down" areas, the bots can move one way, but cannot get back the other.
Disconnects ALL connections from the currently marked area to the currently selected area.
These two commands allow the creation of new nav areas. "bot_nav_begin_area" marks one corner of the area. "bot_nav_end_area" marks the opposite corner of the area and creates it. To cancel the operation, issue a "bot_nav_begin_area" command again.
Creates a new nav area between the currently marked area and the currently selected area, and bidirectionally connects the new area. This command is especially useful for creating sloped nav areas.
Flags the currently selected area as "crouch", requiring bots to crouch (duck) to move through it.
Flags the currently selected area as "jump". This is a hint to the bots that they should jump to traverse this area.
NAVIGATION MESH PROCESSING
Analyze the navigation mesh to determine Approach Points and Encounter Spots. This may take several minutes based on the size and complexity of the map.
NOTE: This command requires one bot to be in the game. The recommended procedure is to save the mesh, add a bot, and quickly enter bot_analyze.
Saves the current navigation mesh to disk. The navigation mesh ("nav" file) is automatically named to correspond to the current map file. For instance, if the map is de_dust.bsp, the nav file will be de_dust.nav.
Clears the current navigation mesh, and loads it from disk.
NAV MESH EDITING
Setting this cvar to 1 allows hand-tuning of the bot's navigation mesh. Once edit mode has been activated, the bot_nav_* commands can be used.
This value determines how high above the ground to draw the "nav mesh" when in nav edit mode. If the terrain is very irregular or highly sloped, it can be useful to increase this value to 10 or 15. The default value is 4.
If nonzero, the analysis phase of map learning will be skipped. This is useful when iteratively hand-tuning nav files. Note that withough this analysis, the bots will not look around the world properly.
Force all bots to walk (disallow running).
If nonzero, all bots will stop moving and responding.
If nonzero, the nav mesh near each bot is drawn.
If nonzero, the "danger" in each nav area is draw as a vertical line. Blue lines represent danger for CTs, and red lines are danger for Ts.
Used for internal debugging of bot navigation.
Used for internal debugging of bot behavior.
Displays the bot version number, and information about the bot's author.
Causes one bot in the map to move to the center of the currently marked area. This is useful for testing the walkability of specific portions of the navigation mesh.
If you made a backup of your liblist.gam just move it back to your /cstrike folder and replace the current one. If you didn't make a backup open liblist.gam with wordpad/notepad.
Replace that line with
Save and close Wordpad/Notepad. The uninstall is now complete. However, the Zbot files are still there, but not used. So if you want to install Zbot again just reverse the procedure.
Turn Dead Island into a true zombie apocalypse and prepare to face over 100x more zombies, including enough ammo you need to fight them off.
These beautiful wallpapers are more than scenic shots of Minecraft, but actual in-game creations from its fan-base.